Fwd: [CUWiN-Dev] 2 radio config howto

[Matt Isaacs]

WPA is typically only supported using wpa_supplicant which is not part of
the node software.  WEP should work, however.  Instructions for freebsd can
be found here:
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/network-wireless.html
specifically Section 27.3.3.1.4 WEP.  These instructions should be similar
to NetBSD.

As far as I know, the software has not been tested using encryption of any
sort, so your mileage may vary.

On 9/21/06, Mike Earnhart <michael.earnhart at gmail.com> wrote:
>
> Are there and docs on enabling wpa - or some restrictive mechanism -
> at UIUC I cannot allow just anyone to connect up (currently I employ a
> bogus dns server to discourage use)?
>
> Pax,
> Michael
>
> On 9/21/06, Brandon Bowersox < brandon at ojctech.com> wrote:
> > Do we have content we could pull together into a HOWTO document /
> > manual page for this?
> >
> > On Sep 20, 2006, at 5:47 PM, dan blah wrote:
> >
> > > ifconfig.ap.tmpl rather :)
> > > On 9/20/06, dan blah <dan.blah at gmail.com> wrote:
> > >> with the 0.7.0 release a node with two suppored radios will by
> > >> default
> > >> set up one radio in 11b hostap mode.  take a look at the
> > >> /etc/ifconfig.client.tmpl
> > >>
> > >> On 9/20/06, Mike Earnhart < michael.earnhart at gmail.com> wrote:
> > >> > I am, Michael Earnhart, and I have 18 CUWiN nodes here at UIUC
> > >> > siebel center.  I have a need to use 2 radios and was wondering
> > >> how I
> > >> > to configure this.  Any help would be appreciated, as I would
> > >> like to
> > >> > avoid spending time developing something that is already developed.
> > >> > Oh and the second radio is used for client connectivity, no
> > >> fancy mesh
> > >> > networking etc.
> > >> >
> > >> > Pax,
> > >> > Michael
> > >> > _______________________________________________
> > >> > CU-Wireless-Dev mailing list
> > >> > CU-Wireless-Dev at lists.cuwireless.net
> > >> > http://lists.chambana.net/cgi-bin/listinfo/cu-wireless-dev
> > >> >
> > >>
> > >>
> > >> --
> > >> Daniel
> > >>
> > >
> > >
> > > --
> > > Daniel
> > > _______________________________________________
> > > CU-Wireless-Dev mailing list
> > > CU-Wireless-Dev at lists.cuwireless.net
> > > http://lists.chambana.net/cgi-bin/listinfo/cu-wireless-dev
> >
> > _______________________________________________
> > CU-Wireless-Dev mailing list
> > CU-Wireless-Dev at lists.cuwireless.net
> > http://lists.chambana.net/cgi-bin/listinfo/cu-wireless-dev
> >
> _______________________________________________
> CU-Wireless-Dev mailing list
> CU-Wireless-Dev at lists.cuwireless.net
> http://lists.chambana.net/cgi-bin/listinfo/cu-wireless-dev
>



-- 
Matthew Isaacs

CUWiN Network Engineer

-- 
Matthew Isaacs

CUWiN Network Engineer
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.chambana.net/mailman/archive/cu-wireless-dev/attachments/20060921/a7c69bb8/attachment.html